Search Results

For internal combustion engines and industrial machinery, it is well recognized that the most cost-effective way of reducing energy consumption and extending service life is through lubricant development. This presentation summarizes our recent R&D achievements on developing a new class of candidate lubricants or oil additives ionic liquids (ILs). Features of ILs making them attractive for lubrication include high thermal stability, low vapor pressure, non-flammability, and intrinsic high polarity. When used as neat lubricants, selected ILs demonstrated lower friction under elastohydrodynamic lubrication and less wear at boundary lubrication benchmarked against fully-formulated engine oils in our bench tests. More encouragingly, a group of non-corrosive, oil-miscible ILs has recently been developed and demonstrated multiple additive functionalities including anti-wear and friction modifier when blended into hydrocarbon base oils.

All internal combustion piston engines emit solid nanoparticles. Some are soot particles resulting from incomplete combustion of fuels, or lube oil. Some particles are metal compounds, most probably metal oxides. A major source of metal compound particles is engine abrasion. The lube oil transports these abraded particles into the combustion zone. There they are partially vaporized and ultrafine oxide particles formed through nucleation [1]. Other sources are the metallic additives to the lube oil, metallic additives in the fuel, and debris from the catalytic coatings in the exhaust-gas emission control devices. The formation process results in extremely fine particles, typically smaller than 50 nm. Thus they intrude through the alveolar membranes directly into the human organism. The consequent health risk necessitates a careful investigation of these emissions and effective curtailment.

This technical paper collection contains 49 papers detailing military vehicle technology. Topics covered include: reliability growth for military vehicles, upgrading readiness, rapidly installed fluid transfer system, robotic technologies, electrical systems modeling and simulation, nanofluid research, and more.

This technical paper collection contains 22 papers on lubricants published from the 2011 Powertrain Fuels and Lubricants Conference.

This technical paper collection contains 8 papers published from the 2011 SAE Brasil Conference.

The 8 technical papers in this collection contain lubricant research and development that is necessary to advance and support new automotive engineering technology. Topics include grease designed to reduce vehicle noise, characteristics of low viscosity engine oil that impact fuel economy and reliability and the characterization of diesel particulate filter ash and how this influences the development of filter regeneration strategies.

The 13 technical papers in this collection cover the work done by student teams in the EcoCAR 2: Plugging in to the Future competition series, sponsored by General Motors and the U.S. Department of Energy. This includes powertrain architecture selection, control system modeling and simulation, and energy storage system design and component packaging.

This specification covers premium quality bolts and screws made of 6Al - 4V titanium alloy.

This set includes: SAE International Journal of Aerospace March 2010 - Volume 2 Issue 1 SAE International Journal of Commercial Vehicles October 2009 - Volume 2, Issue 1 March 2010 - Volume 2, Issue 2 SAE International Journal of Engines October 2009 - Volume 2, Issue 1 March 2010 - Volume 2, Issue 2 SAE International Journal of Fuels and Lubricants October 2009 - Volume 2, Issue 1 March 2010 - Volume 2, Issue 2 SAE International Journal of Materials and Manufacturing October 2009 - Volume 2, Issue 1 March 2010 - Volume 2, Issue 2 SAE International Journal of Passenger Cars - Electronic and Electrical Systems October 2009 - Volume 2, Issue 1 SAE International Journal of Passenger Cars - Mechanical Systems October 2009 - Volume 2, Issue 1 March 2010 - Volume 2, Issue 2

Abstract Electric heavy-duty tractor-trailers (EHDTT) offer an important option to reduce greenhouse gases (GHG) for the transportation sector. However, to increase the range of the EHDTT, this effort investigates critical vehicle design features that demonstrate a gain in overall freight efficiency of the vehicle. Specifically, factors affecting aerodynamics, rolling resistance, and gross vehicle weight are essential to arrive at practical input parameters for a comprehensive numerical model of the EHDTT, developed by the authors in a subsequent paper. For example, drag reduction devices like skirts, deturbulators, vortex generators, covers, and other commercially available apparatuses result in an aggregated coefficient of drag of 0.367. Furthermore, a mixed utilization of single-wide tires and dual tires allows for an optimized trade-off between low rolling resistance tires, traction, and durability.

Abstract The present study aims to join the dissimilar materials such as Dual-Phase (DP) 600 Steel and AA6082-T6 Aluminum (Al) alloy via the friction stir welding (FSW) process with a reduced intermetallic compound (IMC) layer. The five different tool tilt angles of 0°, 0.5°, 1°, 1.5°, and 2° were selected to fabricate the joints. The weld characteristics such as tensile strength, hardness, macrostructure, and microstructure were analyzed. The weld interface was studied by employing an optical microscope and scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) techniques. The joint produced with a 0.5° tilt angle has achieved the highest ultimate tensile strength (UTS) of 240 MPa. The IMCs were identified as Fe2Al8 and FeAl2 from the joint interface studies.

Abstract Direct welding of coated steels to aluminum alloys is challenging due to high energy requirements, decreased weldability, and unstable weld quality. The present study reports the application of a new design approach in vaporizing foil actuator welding (VFAW), where an asymmetric preform shape on the target sheet generated the requisite standoff, enabling direct spot welding of a typical automotive aluminum alloy (6022 T4) and two different zinc-coated steels, galvanized high-strength low-alloy 350 and galvannealed dual-phase 590. The use of the new approach enabled for the first time the ability to spot weld through coating without any preweld surface preparation. Characterization using lap-shear and peel testing revealed strong joints for both the weld pairs (AA 6022 T4-HSLA 350 and AA 6022 T4-DP 590). The weld interface characterized by scanning electron microscopy (SEM) revealed a hierarchical structure and the presence of a typical wavy region.

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract Sound ductile iron (DI) welded joints were performed using developed coated electrode and optimized welding parameters including post weld heat treatment (PWHT).Weldments consisting of weld metal, partially melted zone (PMZ), heat affected zone (HAZ) and base metal were austenitized at 900 °C for 2 hour and austempered at 300 °C and 350 °C for three different holding time (1.5 hour, 2 hour and 2.5 hour). In as-weld condition, microstructures of weld metal and PMZ show ledeburitic carbide and alloyed pearlite, but differ with their amount. Whereas microstructure of HAZ shows pearlite with some ledeburitic carbide and base metal shows only ferrite.

Abstract Reducing a vehicle’s weight is an efficient method to reduce energy consumption. Aluminum alloy is the best material for lightweight automobiles. However, the poor formability of aluminum means that it is difficult to develop stamping dies. This study designs a suitable forming tool for aluminum fenders. A simulation and an experiment are used to analyze the formability of aluminum fenders. A theoretical calculation, experimental testing, and sampling comparison are used to verify the design. The material properties of steel and aluminum are firstly studied and compared. The results show that a traditional S-type blank die face design is not suitable for aluminum because of its low tensile strength and the potential for elongation. A relatively flat trapezoid blank die face design is proposed to smooth the variation. However, a flat die face for a trapezoidal blank limits stretching, so another design is essential to improve the formability.

Abstract The supersession of metallic alloys with lightweight, high-strength composites is popular in the aircraft industry. However, aviation electronic enclosures for large format batteries and high power conversion electronics are still primarily made of aluminum alloys. These aluminum enclosures have attractive properties regrading structural integrity for the heavy internal parts, electromagnetic interference (EMI) suppression, electrical bonding for the internal cells, and/or electronics and failure containment. This paper details a lightweight carbon fiber composite chassis developed at Meggitt Sensing Systems (MSS) Securaplane, with a copper metallic mesh co-cured onto the internal surfaces resulting in a 50% reduction in weight when compared to its aluminum counterpart. In addition to significant weight reduction, it provides equal or improved performance with respect to EMI, structural and flammability performance.

Abstract In this article, forming residual stresses in cold-formed small-radius corner sections are analytically predicted with the consideration of the shift in the neutral axis and the nonlinear strain-hardened material model. The predicted forming stress results in the transverse direction show a trend of increased compressive residual stress in the outer surface and reduced tensile residual stress in the inner surface as the corner radius-to-thickness ratio increases in small-radius bends. In the longitudinal direction, there is no significant change in the residual stress values observed in the inner and outer surfaces with respect to an increase in corner radius-to-thickness ratios. But a considerable decrease in compressive residual stress and an increase in tensile stress values are observed in the midsection areas with an increase in the corner radius-to-thickness ratio.

Abstract In this study, active-passive filling friction stir repairing (A-PFFSR) process was employed to repair the volume defects in friction stir welding (FSW) joints of Al-Cu alloy. The volume defects with varied geometries were first machined into taper holes, which are similar to keyhole defect by a rotational tool with a threaded pin. Then, the keyhole defect was effectively filled with the materials around the keyhole and an additional filler using a number of nonconsumable pinless tools with the shoulders having six spiral flutes. The macro/microstructures, microhardness, and tensile properties of the repaired joints were investigated. The influences of plunge speed on macro/microstructures and mechanical properties of the repaired joints have been analyzed too. It was noticed that decreasing plunge speed was effective to improve the frictional heat and material flow, which increased joint surface integrity avoiding interfacial drawbacks.